Fundamental Plumber Tips for Bathtub Installation

Click Here

Just how do you really feel about How to Install a Bathtub?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a tub isn't precisely brain surgery, however it does require solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately challenging project. If the old tub is conveniently accessible, the task can move rapidly; if you have to open a wall to remove the old tub and position the brand-new tub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Make sure you have certified on your own for the work and are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed task, it is far better to consider using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have already acquired a new tub and also don't require to alter the plan of your previous water system pipes.
Your devices and also material checklist must comprise the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, activate the taps to drain any water staying in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is frequently the case.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipes. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
    Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The former type needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Installing the Tub


    Making use of the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little points.
    The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out level.
    To set up taps, fit the bottom of the outermost versatile faucet port to the proper supply pipeline by making a compression join; then do the exact same for the other tap.
    Switch on the water supply and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bath tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Finally, take care of the bath paneling as explained in the maker's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has actually been used at the very least when as this will resolve it into its final position.

    Getting ready for the Installation


    Firstly, the supporting framework provided with the bathroom must be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the bathtub.
    Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the provided washers.
    Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last placement.

    Tiling Around the Bath tub


    In the location where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall in between the bathroom as well as the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
    You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can break rather early if you do not take into consideration this movement prior to sealing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly readily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water-proof adhesive as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    I'm certainly very serious about How to Install a Bathtub and I really hope you appreciated the new article. Are you aware of anybody else who is excited by the subject? Please feel free to share it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.


    Trustworthy fix? Call.

    Leave a Reply

    Your email address will not be published. Required fields are marked *